1.0 I NSTALLING
THE
M ETER
Installation
The PAX meets NEMA 4X/IP65 requirements when properly installed. The
unit is intended to be mounted into an enclosed panel. Prepare the panel cutout
to the dimensions shown. Remove the panel latch from the unit. Slide the panel
gasket over the rear of the unit to the back of the bezel. The unit should be
While holding the unit in place, push the panel latch over the rear of the unit
so that the tabs of the panel latch engage in the slots on the case. The panel latch
should be engaged in the farthest forward slot possible. To achieve a proper seal,
tighten the latch screws evenly until the unit is snug in the panel (Torque to
approximately 7 in-lbs [79N-cm]). Do not over-tighten the screws.
installed fully assembled. Insert the unit into the panel cutout.
Installation Environment
The unit should be installed in a location that does not exceed the maximum
operating temperature and provides good air circulation. Placing the unit near
BEZEL
PANEL
devices that generate excessive heat should be avoided.
The bezel should be cleaned only with a soft cloth and neutral soap product.
Do NOT use solvents. Continuous exposure to direct sunlight may accelerate the
aging process of the bezel.
LATCHING
SLOTS
PANEL
LATCH
PANEL CUT-OUT
-.00
3.62 +.03
PANEL
GASKET
PANEL
MOUNTING
SCREWS
LATCHING
TABS
-.0
(92 +.8 )
-.00
-.0
1.77 +.02
(45 +.5 )
2.0 S ETTING
THE
S WITCHES
AND
J UMPERS
The meter has switches that must be checked and/or changed prior to
applying power. To access the switches, remove the meter base from the case by
firmly squeezing and pulling back on the side rear finger tabs. This should lower
the latch below the case slot (which is located just in front of the finger tabs). It
is recommended to release the latch on one side, then start the other side latch.
Excitation Range Jumper
Set-Up DIP Switches
Two banks of DIP switches are located inside the meter. The 9 position bank
of switches is used for calibrating the meter. The values of these switches is
discussed in section 5.0 Calibrating the Meter.
The bank of 4 switches located near the front display are used for the
selection of decimal points and backlight annunciator. Selecting “ON” position
enables the function.
A jumper is used for selection of the 5 or 10 volt range. It is important that
only one jumper position is used at a time.
SWITCH
1
2
3
4
FUNCTION
Decimal Point 1 (000.0)
Decimal Point 2 (00.00)
Decimal Point 3 (0.000)
Backlight Annunciator for Units Label
PAXLSG Jumper Selection
FRONT DISPLAY
JUMPER SELECTIONS
The
indicates factory setting.
Main
Circuit
4
3
2
1
D.P./ BACKLIGHT
Board
ON
EXCITATION SELECT
10V
EXCITATION
SELECT
5V
OFFSET
SPAN
GAIN
COARSE FINE
1 2 3 4 5 6 7 8 9
OFFSET
REAR TERMINALS
REAR TERMINALS
4
相关PDF资料
PAXLTC00 METER THERMOCOUPLE 4-DIGIT
PAXLVA00 VOLTMETER AC 3 1/2-DIGIT
PAXLVD00 VOLTMETER DC 3 1/2-DIGIT
PAXTM100 TIMER DISPLAY 1/8 DIN PRESET 6 D
PB-1583-TF BOX ABS 4.37X3.12X2" BK 1=10PCS
PB-1583 BOX ABS 4.37X3.12X2" BK 1=10PCS
PBS-11273 BOX ABS 6.30" X 3.75" X 1.41" BK
PBS-11275 BOX ABS 6.30" X 3.75" X 1.41" BK
相关代理商/技术参数
PAXLT000 制造商:Red Lion Controls 功能描述:METER, TC/RTD TEMP WITH DUAL RELAY 制造商:Red Lion Controls 功能描述:TC/RTD TEMP WITH DUAL RELAY
PAXLT0U0 制造商:Red Lion Controls 功能描述:METER, UL LISTED TC/RTD TEMP W/ D RELAY 制造商:Red Lion Controls 功能描述:UL LISTED TC/RTD TEMP WITH DUAL
PAXLTC00 功能描述:METER THERMOCOUPLE 4-DIGIT RoHS:否 类别:工业控制,仪表 >> 仪表 - 面板,数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030
PAXLVA00 功能描述:VOLTMETER AC 3 1/2-DIGIT RoHS:是 类别:工业控制,仪表 >> 仪表 - 面板,数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030
PAXLVD00 功能描述:VOLTMETER DC 3 1/2-DIGIT RoHS:是 类别:工业控制,仪表 >> 仪表 - 面板,数字 系列:PAX®LITE 标准包装:12 系列:* 其它名称:Q7072030
PAXOEMS1 制造商:Red Lion Controls 功能描述:SOFTWARE AND USB CABLE RS232
PAXOEMSS 制造商:Red Lion Controls 功能描述:SOFTWARE AND CABLE RS232 制造商:Red Lion Controls 功能描述:SOFTWARE AND CABLE, RS232 制造商:Red Lion Controls 功能描述:SOFTWARE AND CABLE, RS232; For Use With:PAXI Counter Display; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes
PAXP0000 制造商:Red Lion Controls 功能描述:Meter, Process, 5 Digit .56" Red LED Display, Power: 85-250 VAC 制造商:Red Lion Controls 功能描述:PROCESS INPUT FIELD 制造商:Red Lion Controls 功能描述:Process Meter 制造商:Red Lion Controls 功能描述:PROCESS METER, 85VAC TO 250VAC; No. of Digits / Alpha:5; Meter Function:DC Milliamps / DC Volts; Meter Range:-2mA to +26mA / -1V to +13V; Digit Height:14.2mm; Panel Cutout Height:44.96mm; Panel Cutout Width:91.95mm ;RoHS Compliant: Yes